Technicolor

From Indie IT Wiki
Revision as of 17:09, 29 December 2015 by imported>Plittlefield (→‎Thomson Technicolor TG582n TG585 Changing The LAN Fixed IP Address)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

Technicolor SA was formerly Thomson SA and the long history of the company can be found here.

Thomson Technicolor TG582n TG585 User Guide

http://help.demon.net/files/2013/03/TG582n-User-Guide.pdf

Thomson Technicolor TG582n TG585 Command Line User Guide

http://wiki.aa.org.uk/images/3/33/TG582n_CLI_Guide_v1.0_public.pdf

Thomson Technicolor TG582n TG585 Changing The Network Settings

http://www.spark.co.nz/content/dam/kb/private/attachments/13805/Changing-the-TG582n-Network-Settings.pdf

Thomson Technicolor TG582n TG585 Changing The LAN Fixed IP Address

The Thomson TG585 is normally supplied by the likes of Plus.net pre-configured for easy connection, that is of course if you want to use their settings.

These instructions are based around the modem having an original IP address of 192.168.1.254 and achieving a target IP address range of 10.0.0.1 – 10.0.0.254, with the router having the IP address of 10.0.0.138.

  1. Browse into the router with the standard 192.168.1.254 address.
  2. Clink 'Disconnect' to disconnect the internet service.
  3. Click 'Home Network' then 'Interfaces'
  4. Click 'Local Network'
  5. Click 'Configure'
  6. Under 'DHCP Pools' > Click 'Add'
  7. Fill out the details as below:
    • Start Address: 10.0.0.1
    • End Address: 10.0.0.254
    • Subnet mask: 255.0.0.0
    • Server: 10.0.0.138
    • Gateway: 10.0.0.138
    • Primary DNS: 10.0.0.138
  8. Click on 'Home Network' then 'Devices'
  9. Click 'Configure'
  10. Delete any devices that have the original 192.168.1.x address. If you have a lot of these, it may be quicker to run the 'hostmgr flush' CLI command from a Telnet session .
  11. Click 'Interfaces'.
  12. Click 'Local Network'
  13. Click 'Configure'
  14. Click ‘delete’ assocated with LAN_private. If you do not have the Delete button, you did not delete all the active devices. Or try ‘hostmgr flush’ from a telnet session.
  15. You may now need to renew your computers IP address
  16. Browse into the router under the new 10.0.0.138 address. And 'Home network' then 'Interfaces'
  17. Click on 'Local Network'
  18. Click 'Configure'
  19. Next to the old 192.168.1.254 IP Address, click Delete. If ‘Delete’ is not there, you have a computer that is still using the 192.168.1.254 address.
  20. Click 'Broadband Connection'
  21. Click 'Connect'

http://www.spark.co.nz/help/internet-data/equipment/technicolour/technicolor-tg582n-help-and-support/change-lan-settings-technicolor-modems/

Telnet Access

If you want to access the modem via Telnet you can find a useful tutorial here

http://npr.me.uk/telnet.html

Fix VOIP

Change the VCI setting on modem from 35 to 102. Now the phones work.

Enable Reply To ICMP Pings From WAN

Log in to the modem via Telnet, and enter the following commands...

service system list name=PING_RESPONDER expand=enabled
service system ifadd name=PING_RESPONDER group=wan
saveall
exit

Then test with the following Linux command...

MYINETIP=$( curl -s ifconfig.me ) && ping -c3 $MYINETIP

Open Ports To Office Server

Web Interface

Toolbox > Game & Application Sharing > Configure > Drop Down Menu > Device > Add

Telnet Interface

:saveall

List Open Ports

Web Interface

Toolbox > Game & Application Sharing

Telnet Interface

:service host list

Change Name Of Connected Network Device

Web Interface

Home Network > Ethernet > Unknown-00-22-15-ce-a2-a7 > Configure > Information > New Name > Server > Apply

Telnet Interface

:saveall

Backup Modem Configuration

Technicolor Gateway > Configuration > Save or Restore Configuration > Backup current configuration

Enable Remote Assistance / Remote Access.

1. Browse to the Technicolor Gateway GUI.

2 Complete and check the following parameters:

Mode: Select the mode that you want to use.

URL: Contains the URL that must be used to access the Technicolor Gateway from the Internet.

User name and Password: Contains the user name and password are needed to access your Technicolor Gateway remotely. If wanted you can change the automatically generated password in the Password box.

3 Click - Enable Remote Assistance